Famco Flue Liner Replacement Nationwide

Famco Flue Liner Replacement: The Brentwood Owner’s Guide

We stock and install Famco-compatible flue liner replacement parts throughout Brentwood, with most jobs running between $2,400 and $4,800 installed depending on liner diameter and chimney height. The work typically takes one day, and we carry the common Famco flex liner sizes on the truck so we’re not making you wait on a shipping delay. Most Brentwood homeowners discover the liner failed either through a camera inspection after years of deferred sweeping, or because rust flakes started showing up in the firebox and they couldn’t figure out where the metal was coming from.

Call (934) 935-3847

Your flue doesn’t care how the fire looks. It cares how it breathes. And when a Famco liner gives out, the symptom is rarely dramatic. It’s usually pinholes, a split seam, or corrosion that’s been quietly working its way through the stainless for a decade or more. By the time you see it, the liner owes you nothing.

Key Takeaways:

• We install Famco-compatible liners in Brentwood, typically same-week scheduling.
• Installed cost runs $2,400-$4,800 for most single-story and two-story chimneys.
• Camera inspection before and after is included, so you see exactly what we see.
• 90-Day Done Right Promise in writing on every liner job.
• We’re an independent local shop, not affiliated with Famco, and we’re fine telling you when a liner can wait.

Which Famco Models This Applies To

Famco makes flue liners in a few distinct lines, and the replacement path depends on which one you have. The most common in Brentwood homes is the Famco Flex-Series, which comes in 4-inch through 8-inch diameters and is sized for gas, oil, and wood applications. There’s also the Famco rigid liner line, which shows up less often in residential work but matters if your chimney has an offset that flex can’t navigate cleanly.

Here’s the compatibility gotcha most people don’t know: Famco flex liners are sized by inside diameter, but the outside diameter varies with the wall thickness. A 6-inch liner with a .005 wall won’t always swap cleanly with a 6-inch liner with a .010 wall if your existing top plate and connector were fit to the old profile. When we come out for a Famco flue liner replacement in Brentwood, we measure the old liner’s OD, not just the ID, before quoting. That’s how you avoid a job where the new liner is an eighth-inch too fat to seat into the existing tee.

On the OEM-versus-aftermarket question: Famco liners are good stainless, but they’re not magical. We’ve installed Famco liners and we’ve installed equivalents from DuraFlex and HeatShield. The difference that matters on Long Island is the alloy. For oil-fired systems in Brentwood, the exhaust runs acidic, and a 316L liner will outlast a 304 by years. Famco offers both, so the “brand match” matters less than the grade of stainless underneath it. We’ll tell you which one your system actually needs, and charge for the part accordingly.

Signs Your Famco Flue Liner Replacement Is Failing

• Rust flakes or metallic grit in the firebox or around the cleanout. This is the classic Long Island tell. Condensation inside the liner eats at the stainless from the inside, and gravity does the rest. If you see brownish flakes that look like coffee grounds, that’s liner material, not ash.
• A lingering sulfur or exhaust smell in the house, even with the damper open. Pinholes let flue gas escape into the chimney cavity, and the smell eventually finds its way through mortar joints and cracks. This is not a “burn it hot and it’ll clear” situation.
• Visible staining or efflorescence on the exterior chimney brick. When combustion gases leak through a failed liner into the masonry, the moisture and acids migrate outward and leave white chalky deposits on the brick face. In Brentwood’s freeze-thaw winters, that moisture also spalls the brick from inside.
• Your sweep’s camera shows delamination, sagging, or a split seam. First-degree creosote is a brush job. Third-degree is a glaze. A split seam is neither. Camera footage and a plain-English verdict, every time, no exceptions.
• The liner has pulled away from the top plate or the tee connection at the bottom. This often shows up after a windstorm when the liner was never properly secured. It’s repairable in some cases, but if the liner has been whipping in the flue for a season, we’re usually replacing it, not re-clamping it.

Replacement Cost & What’s Included

An installed Famco-compatible flue liner replacement in Brentwood costs between $2,400 and $4,800 for most homes. A straightforward single-story chimney with a straight run and an existing insulated chase sits at the low end. A two-story with roof access complications, a deteriorated clay tile liner that needs breaking out first, or a liner that’s fused to the old insulation at the top plate pushes toward the high end.

The price we quote covers the liner kit (flex or rigid, in the grade your fuel type requires), the top plate and cap, the tee and connector at the appliance, insulation where needed, removal and disposal of the old liner, and the full install including a camera verification pass after the liner is seated. The number you hear on the phone is the number on the invoice. No-hassle upfront pricing before a single tool comes off the truck.

If the city of Brentwood or Suffolk County requires a permit or post-install inspection for liner work, we handle that paperwork. The completed job carries our 90-Day Done Right Promise. If it’s not right, one call brings Wendell and the crew back at no additional cost.

DIY or Call Us?

Flue liner replacement is not a weekend project. You’re working at height, often on a roof pitch that’s unforgiving, and the liner has to be fed down through the flue without tearing on the existing clay tile or snagging on offset bricks. A torn liner is worthless before it’s ever connected. We’ve pulled more than a few DIY attempts out of Brentwood chimneys where the homeowner got the liner halfway down, bound it up, and couldn’t pull it back out.

What you can safely check yourself is the visible stuff: look at the top plate from ground level, check for rust stains on the chimney exterior, and keep an eye on what’s landing in the firebox. Beyond that, this is a job for someone who does it every week and has the rope, the cone, and the camera to confirm it’s seated right. If you’re in Brentwood and want a straight answer about whether your Famco liner actually needs replacing or just needs a sweep, call Wendell at (934) 935-3847. If it needs doing, we’ll do it right. If it doesn’t, we’ll tell you that too.

FAQs