Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Repair in Brentwood: What to Know First
We repair Olympia Chimney systems throughout Brentwood, and most jobs are done in a single visit. You’ll get a straight price before we start, and if the flue doesn’t actually need the work, we’ll tell you that before you spend a dime. Call us at (934) 935-3847 and Wendell or one of the crew will talk you through what you’re seeing.
This page is for homeowners in Brentwood who own an Olympia Chimney product and have been told it needs repair or replacement. Maybe you’ve got spalling brick below the cap, a mortar joint that’s turning to sand, or a flashing leak that’s been dripping into the attic. Olympia Chimney systems are common around here, especially in the capes and colonials near Brentwood State Park, and we’ve been inside enough of them to know exactly what fails and why. As an independent Olympia Chimney service provider, we’re not tied to the manufacturer’s replacement schedule. We fix what’s broken and leave what isn’t.
How Olympia Chimney Products Fail – and How We Fix Them
Your flue doesn’t care how the fire looks. It cares how it breathes. Olympia Chimney products are solid equipment, but every brand has weak spots, and we see the same patterns repeat across Brentwood homes year after year.
- Olympia galvanized chase covers rusting through at the seams. The factory chase cover on many Olympia Chimney chase installations is galvanized steel, and on Long Island, between the salt air and the freeze-thaw cycles, those seams start to go in eight to twelve years. Water gets in, drips down the chase, and soaks the insulation around the flue. We replace the cover with stainless and reseal the chase top. The Olympia flue pipe inside is often still perfectly fine, which is why we check before quoting a full rebuild.
- Mortar cracking at the roofline on Olympia masonry chimneys. This isn’t an Olympia defect. It’s a Brentwood winter reality. The mortar at the top three or four courses absorbs water, freezes, and crumbles. What we see on Olympia Chimney installations is that the flue liner itself tends to hold up while the surrounding masonry needs repointing. We do full tuckpointing and can treat the brick with a breathable waterproofing that stops the cycle without trapping moisture.
- Flashing separation where the Olympia chase meets the shingles. The factory flashing on many older Olympia Chimney prefab units is aluminum, and after a decade of ice and wind, it lifts away from the roof line. Water follows the gap straight down. We pull the old flashing, replace it with custom-bent step flashing, and seal the transition properly. This is one of the most common calls we get in Brentwood after a hard winter.
- Liners cracked by thermal shock in Olympia Chimney wood-burning systems. When a clay tile liner heats up fast and cools down hard, it cracks. Olympia Chimney fireplaces and stoves that burn hot, dry wood are more prone to this than the brand’s gas venting products. We see vertical cracks and sometimes missing tile sections on camera. The fix is usually a DuraFlex or HeatShield liner, sized to the Olympia unit and installed to code. Your Olympia firebox stays, and the flue gets a second life.
- Caulk failure around the Olympia cap and crown. The crown on a masonry chimney is meant to shed water, but the factory seal between the crown and the top flue tile on Olympia Chimney installations tends to dry out and pull away over a few summers. Once that seal goes, water sits in the gap and works its way into the brick below. We repair the crown with a proper wash and reseal around the flue, so water stops getting in where it shouldn’t.
Our Olympia Chimney Chimney Repair Process
Here’s what happens when you call us about your Olympia Chimney system in Brentwood.
- 1
You call, a person answers. Wendell or one of the crew picks up. You tell us what you’re seeing. We’ll give you an honest read on whether it sounds like a repair or a replacement, and we’ll set a real arrival window. No call center, no phone tree, no voicemail box at midnight.
- 2
We inspect the whole chimney, not just the complaint. The sweep who shows up at your door will look at the firebox, the flue, the chase or masonry, the flashing, the cap, and the surrounding roof. We run a camera down the flue. You’ll see the footage yourself.
- 3
We show you what’s wrong in plain English. The camera footage and a plain-English verdict – every time, no exceptions. If the liner is cracked, you’ll see the crack. If the mortar is soft, you’ll see it crumble. If nothing’s wrong, we’ll tell you that too. If it needs doing, we’ll do it right. If it doesn’t, we’ll tell you that too.
- 4
You get a fixed price before a single tool comes off the truck. No split pricing, no surprise line items. The number we quote is the number you’ll pay, whether we use OEM Olympia Chimney parts or a quality aftermarket equivalent that makes more sense for your budget. We explain the trade-off before you decide.
- 5
We do the repair and test the result. Mortar repointing, tuckpointing, flashing replacement, rebricking, waterproofing, liner work, or a full rebuild if the structure calls for it. When we’re done, we fire-test the system and run the camera again, so you can see the before and after.
- 6
We leave the hearth cleaner than we found it. Drop cloths down, tools up, and everything swept before we shake your hand. The 90-Day Done Right Promise is stamped on your invoice. If it’s not right, one call brings Wendell back.
What Olympia Chimney Chimney Repair Costs in Brentwood
Here’s what you can expect to pay for the most common Olympia Chimney repairs in Brentwood. These are real ranges based on the work we’ve done around town.
- Tuckpointing and mortar repointing: $450 to $1,200, depending on how many courses need work and how high the scaffold has to go.
- Spalling brick repair (small to medium sections): $350 to $900, including brick removal, replacement, and tooling to match the existing joints.
- Chimney waterproofing (full treatment): $300 to $700, breathable sealant applied to clean, sound masonry.
- Flashing repair or replacement: $550 to $1,400. The price depends on whether we can patch or need to remove shingles and bend new flashing around the base.
- Partial chimney rebuild (top courses and crown): $1,800 to $4,500. A full teardown and rebuild from the roofline up runs higher, and we’ll only recommend it if the structure genuinely calls for it.
- Liner inspection with camera report: Free with any repair job. If you just want the camera and a verdict, we charge a small inspection fee inside the county.
What moves the price is access, height, and how far the damage has gone. A two-story colonial with a steep roof pitch near Brentwood State Park will cost more to work on than a one-story cape with a walkable ridge. First-degree creosote is a brush job. Third-degree is a glaze – catch it early. Call (934) 935-3847 for a straight quote, and remember: no trip charge inside the county, and estimates are free.
Why Brentwood Homeowners Call Top Hat Chimney for Olympia Chimney Work
Wendell Pike started Top Hat Chimney in 1999 and has been working the same Brentwood neighborhoods ever since. Ask anyone on your street. If they’ve got a chimney, there’s a good chance we’ve been on their roof. That’s the whole business model. We answer the phone, we show up in uniform, and we put our name and license number on every job. Wendell grew up in San Diego and learned the trade at Southwestern College in Chula Vista, but he’s spent the better part of two decades hauling brushes and rods up onto Long Island rooftops, including plenty of capes and colonials over near Brentwood State Park.
We work on Olympia Chimney products every week, which means we know what’s an OEM part situation and what isn’t. We also install and service DuraFlex, HeatShield, and Gelco, so if your Olympia Chimney unit needs a liner or a component the factory doesn’t sell anymore, we’ve got a quality path forward. You get a background-checked, uniformed tech, a live person on the phone around the clock, and the 90-Day Done Right Promise in writing. Seniors and veterans always get 10% off, repairs over $200 knock $40 off the bill, and if another company gave you a written estimate, we’ll give you a free second opinion.
FAQs
Most Olympia Chimney repairs in Brentwood run between $350 and $1,400, with larger rebuilds ranging from $1,800 up. Tuckpointing starts around $450, flashing work around $550, and waterproofing runs $300 to $700. The exact number depends on access, height, and how much of the structure has failed. Call (934) 935-3847 and we’ll walk you through what your specific job should cost before you commit to anything.
We can source OEM Olympia Chimney parts when they’re available and they still make sense for the job. When the factory has discontinued a component or the original design was doomed to fail again, we use quality aftermarket parts from DuraFlex, HeatShield, or Gelco. We show you the options and the price difference before we order anything, so you’re never paying for a brand sticker without knowing it.
As an independent Olympia Chimney service provider, we don’t void warranties by doing repair work. If your unit is still under factory warranty, we’ll flag that before we touch anything and help you decide whether a manufacturer claim makes more sense than paying out of pocket. When the warranty is expired or doesn’t cover the failure, we get the repair done right without pretending the warranty department is going to save you.
Most non-emergency repair jobs get scheduled within a week, and weather-permitting, we’ll give you a real arrival window and call if it slips. The urgency here is seasonal. If you’ve got a water leak or a damaged flue, you don’t want to wait until the next storm cycle. Once a year, burn or no burn. Chimneys break in the off-season too. Call (934) 935-3847 and we’ll get you on the books.
That depends entirely on what the camera shows. If the chase is sound, the flue is clear, and the problem is mortar or flashing or a rusted cap, a repair is the right call and will buy you years. If the liner is cracked or the structure is separating, replacement might be smarter. We’ll never recommend a rebuild you don’t need. The camera footage and a plain-English verdict, every time, no exceptions.
If you’re in Brentwood and your Olympia Chimney system needs work, call (934) 935-3847 today. We’ll put you on the schedule, show up when we say we will, and tell you the truth about what your chimney actually needs.
Written by Wendell Pike, Owner, Top Hat Chimney at Top Hat Chimney, serving Brentwood and nearby areas.